GR Pottery Forms - 6' x 12' Rounded Rectangle

The first step to avoid warping is properly compressing one side of the slab completely. We then drape the slab over the Form, and compress the other side while it’s on the Form.

After compression and completing any foot or lip prep (adding spacer), we don’t touch the object until it is quite a stiff leather hard (the Form pops off on its own). You should be able to press a finger nail into the clay and leave a mark, but you should not be able to form an impression with the soft part of your finger.

If you are making objects with a lip you must use a spacer.

Once the clay is a stiff leather hard, we lift it off the Form. If it bends or moves in any way after lifting it off, you’ve taken it off too soon. We’ve found that removing the slab too soon is the single most significant factor towards warping the piece.

Also, trying to flip it over before it dries enough may result in the ends to start curling upward. We understand it can be difficult to “be there at the right time,” but the importance of removing the piece at the right time cannot be understated.

The second most common way the slabs will warp is that there is a draft in your room caused by a fan, heater, breeze or room air flow. Make sure to let the object dry evenly in a still area. Speed is not a factor. Plastic or the use of weighted sacks can also cause uneven drying.

Steps to Avoid Warping when Creating a Plate:

1. Use a Slab Roller to roll-out the clay
2. Use a Rib to compress the clay two different directions on one side
3. Add texture if necessary
4. Drape, the smooth/textured side down, of moist clay onto form and press gently and evenly to sides to push out any air trapped underneath.
5. Use Rib again to compress clay to the Form - firmly and evenly
6. Cut strips of clay using Foot Maker
7. Let piece and foot strips rest for about 20-30 minutes to stiffen clay slightly
8. Score area and add water to score marks to then attach the feet
9. Attach foot strips to create border around piece. No more than 1/2 an inch from edge and 8 inches from widest point
10. Use Modeling Tool to clean the places where foot meets the body on all sides
11. If the piece has a rim, lift off work surface and place a Spacer underneath
12. Press the edge of the rim down to work surface to create a slight pitch
13. Let piece set for 4-8 hours uncovered in non draft area until edges start to curl up
14. Key is even drying - not length of drying. Sometimes putting plastic on top creates uneven drying
15. Now flip piece over without flexing or stretching the clay. Then press on inside center downward to level out any curling that might have happened
16. Use Surform Rasp to clean edges and carve smooth any uneven areas
17. Use Notched Rib to burnish the edges even smoother. With non grog clay you can use a Sponge to smooth edges but do not get clay too wet
18. Now is a great time to add your favorite underglaze or carve into piece
19. Let dry and bisque fire.  Stacking should not affect warping

What determines the size of the Form?

Form sizes are measured from the back side of the Form which is also the largest part of the Form. Measurements are approximate.

If you are trying to determine what size to make, there are many factors involved. Factors would include: The size of your lip, shrinkage of clay and firing temperature.

The Depth of Standard Forms are 3/4 inch. If you want to determine the center/inside measurement, it would be 1.5 inches smaller than the Form measurements.

Slim Forms are 1/2 inch in depth. 

Deeper Options:

If you are looking for a deeper option you can use the general rule that if a shape is 1.5 inches different in measurement it will stack with the size above or below it. We offer "Stacks" to make this available to you. 

Due to the depth limitations of the wood we feel it is not practical to glue wood together to make deeper shapes. If you need this depth then it becomes more cost effective to use plaster molds.

How do I avoid “seams” when making deeper bowls or platters using one or more stacked plates together?

Unfortunately, one of the disadvantages of stacking the Forms is that it is difficult to avoid creating small "seams" between them, as there will remain a small gap unless the Forms themselves were glued together. When we use Stacked Forms to create bowls or plates with greater depth, we have found it is most effective to use a rib or ribbon tool to smooth out the seam lines when the piece is a very stiff leather hard.

Do I need to use a release agent?